Rocker Switch 15 Amp
Call Only
This is the on/off switch, located on both the waste oil burner and fuel pump assembly.
Round Face Gauge (old style)
Call Only
Located on the front of the electrical box on the burner housing. Used on older model heaters and can be used as a replacement for the square face gauge if needed. New models standard build is with the square face gauge.
Snap Switch (New Style)
Call Only
This new style snap switch screws on to the fuel pre-heater block with two little screws. Located on the fuel pre-heater block assembly.
Snap Switch (Old Style)
Call Only
The old style snap switch screws into the side of the fuel pre-heater block. Located on the fuel pre-heater block assembly.
Spin On Filter Assembly (New Style)
Call Only
All new units purchased come standard with this spin-on fuel filter and housing. This housing and spin-on fuel filter can also be used to convert your old style from the pancake serviceable fuel filter to the new style spin-on fuel filter.
Spin On Filter Replacement (New Style)
Call Only
Spin-On fuel filter replacement (filter only), located on the fuel pump assembly.
Square Face Gauge
Call Only
Located in the front of the electrical box on the waste oil burner assembly.
Straight Fitting
Call Only
This fitting is used in multiple locations as follows: (2) Attached to the back side of the square faced air gauge on the waste oil burner electrical box. (1) Attached to the fuel pre-heater block
Suntec Fuel Pump
Call Only
The Suntec fuel pump is located on the outside of the fuel pump assembly housing.
Suntec Gasket
Call Only
This gasket is located inside of the Suntec fuel pump on the outside of the fuel pump assembly.
Suntec Strainer
Call Only
This Suntec stainless strainer filter is located inside of the Suntec fuel pump located on the outside of the fuel pump assembly.
Target Plate (250-350 Bolt On Door Style – Square Bottom)
Call Only
This target plate is located inside the cleanout door, opposite of the waste oil burner. This target plate is for the OWH-250 & OWH-350 models only. If you have a unit built before 2005, please call to confirm that this is the correct target plate for your unit.
Target Plate (250-350 Swing Door Style)
Call Only
The target plate is located inside the cleanout door, opposite of the waste oil burner. This target plate is for OWH & EH-250 & OWH & EH-350 models only. If you have a unit built prior to 2009, please call to confirm that this is the correct target plate for your unit.
Thermocouple 1 Foot
Call Only
This specific thermocouple is located between the fuel pre-heater block assembly and the fuel pre-heater block circuit board. This is the standard size thermocouple on all new units, both OMNI and the Econo Heater models.
Thermocouple 3 Foot
Call Only
This part is located in the waste oil burner housing between the fuel pre-heater block assembly and the fuel pre-heater circuit board. This size of thermocouple is for an outdated model and incurs a 3 week lead time. For units 10 years and older. Please call to verify this is the correct thermocouple for your waste oil heating unit.
Thermostat, Snap Action
Call Only
The snap action wall thermostat comes standard with all new OMNI and Econo Heater waste oil heaters.
Transformer (120V)
Call Only
The transformer is located at the top of the waste oil burner housing. Sold pre-mounted to the hinged plate on both the OMNI compressed air burner system and the Econo Heater pressure burner system.
Valve Solenoid (120V)
Call Only
The valve solenoid is located on the waste oil burner, underneath the electrical box. A second one is also located on the fuel pump assembly.
White Flange Gasket (Burner Door)
Call Only
This gasket is located on the waste oil burner housing mounting flange for both the OMNI compressed air burner system and the Econo Heater pressure burner system.