Waste Oil Burner Parts
20 Amp Fuse
Call Only
This fuse is located inside of the inline fuse holder and can be found between the terminal block and the power switch within the electrical box on the waste oil burner.
90 Degree Fitting
Call Only
The 90 degree fitting is used to connect the fuel line from the valve solenoid to the fuel pre-heater block on the waste oil burner.
Air Band
Call Only
The air band is used on both the OMNI compressed air burner system and the Econo Heater pressure burner system. Located on the waste oil burner housing.
Air Compressor Carbon Plate
Call Only
The carbon plate is located in the air compressor motor behind the removable plate. Carbon plate is accessed the same way as the vanes.
Air Compressor Motor (OMNI line only)
Call Only
The motor air compressor is a standard build on all OMNI waste oil heaters. Located on the bottom of the waste oil burner assembly.
Air Compressor Squirell Cage
Call Only
This squirrel cage fan is located inside of the waste oil burner housing between the air-band and the air compressor motor.
Air Compressor Vanes
Call Only
Vanes are located inside of the air compressor motor on the OMNI waste oil burner.
Air Filter Canister
Call Only
The air filter canister is located on the air compressor motor on the OMNI waste oil burner.
Air Filter Replacement
Call Only
Replacement filter for the air filter canister located on the air compressor motor on the OMNI waste oil burner.
Amber Light
Call Only
Located on the front of the electrical box on the waste oil burner assembly. Compatible with both OMNI and the Econo Heater line of waste oil equipment.
Clear Hose (Oil & Air Lines)
Call Only
The clear plastic hose/line is for both the air line and fuel line. The air line goes from the compressor into the fuel pre-heater block and the fuel line goes from the solenoid into the fuel pre-heater block.
Flame Cone With Ring
Call Only
The flame cone is located at the tip of the waste oil burner tube which fits in the burner tube housing around the nozzle.
Flat Rope Gasket
Call Only
This item is $1.25 per foot and is used on the OMNI old style bolt on clean out door opposite of the waste oil burner. This flat rope gasket is also currently used on the new style OMNI and Econo Heater 75,000 BTU waste oil heater models.
Green Light
Call Only
Located on the front of the electrical box on the waste oil burner assembly. Compatible with both OMNI and the Econo Heater line of waste oil equipment.
Inline Fuse Holder
Call Only
Inline safety fuse located inside of the electrical box on top of the waste oil burner.
Muffler Filter (Old Style)
Call Only
This filter is only used on the older style OMNI heaters. Located on the air compressor motor on the old style OMNI waste oil burners. New style and standard build is the black air filter canister. You can retro-fit the new style air filter canister to the old style waste oil burners if you choose.
Photo Eye Only
Call Only
Photo eye (flame sensor) only. Located underneath of the transformer lid. Flip back the transformer to access this part.
Photo Eye/CAD Cell – With Wire Brackets
Call Only
Comes complete with the flame sensor, wires and brackets. Located underneath of the transformer lid. Flip back the transformer to access this part.
Rocker Switch 15 Amp
Call Only
This is the on/off switch, located on both the waste oil burner and fuel pump assembly.
Round Face Gauge (old style)
Call Only
Located on the front of the electrical box on the burner housing. Used on older model heaters and can be used as a replacement for the square face gauge if needed. New models standard build is with the square face gauge.
Square Face Gauge
Call Only
Located in the front of the electrical box on the waste oil burner assembly.
Straight Fitting
Call Only
This fitting is used in multiple locations as follows: (2) Attached to the back side of the square faced air gauge on the waste oil burner electrical box. (1) Attached to the fuel pre-heater block
Transformer (120V)
Call Only
The transformer is located at the top of the waste oil burner housing. Sold pre-mounted to the hinged plate on both the OMNI compressed air burner system and the Econo Heater pressure burner system.
Valve Solenoid (120V)
Call Only
The valve solenoid is located on the waste oil burner, underneath the electrical box. A second one is also located on the fuel pump assembly.
White Flange Gasket (Burner Door)
Call Only
This gasket is located on the waste oil burner housing mounting flange for both the OMNI compressed air burner system and the Econo Heater pressure burner system.